manualshive.com logo in svg

UNIBLOC PD600, Operation & Service Manual, Page: 15 / 55

Share
Download
UNIBLOC PD600 Operation & Service Manual Download Page 15

UNIBLOC-PD Operation & Service Manual: PD600-677  15

4.4.1.4 Cover and Rotor Removal- FoodFirst 

FoodFirst Rotors

 do

 not require locking mechanisms and work in tandem with the 

FoodFirst Front Cover

. The 

FoodFirst system utilizes two sets of of removable wear rings. One set of wear rings are located in the front cover 

(

Front Cover Wear Rings

) while the other set are located in the rotors (

Rotor Wear Rings

). It is important to take 

care when maintenancing FoodFirst pumps. Damage to the wear rings, rotors, and front cover may prevent the pump 

from operating as intended.

4.4.1.4.0 FoodFirst Front Cover Removal 

(reference  figs. 4.1, 4.4.1)

Remove the 

Front Cover Nuts 

(see fig. 4.1). Carefully remove the

 FoodFirst Front Cover, 

taking caution not to 

damage the 

Wear Rings

. The 

Rotor Wear Rings 

may adhere to the 

Front Cover Wear Rings

 and dislodge from the 

Rotors

 during 

Front Cover 

removal. Store any loose wear rings in a safe place.

4.4.1.4.1 FoodFirst Front Cover Wear Ring Removal- Standard Front Cover 

(ref. fig. 4.4.2)

The 

Front Cover Wear Rings

 may be removed from the 

Front Cover

 by gently pulling them out of the cover.  Once 

removed, be sure to store wear rings in a safe place.

4.4.1.4.2 

FoodFirst Front Cover Wear Ring Removal- High Pressure (HP) Cover

 (ref. fig. 4.4.3)

The 

Front Cover Wear Rings

 may be removed from the 

Front Cover

 by gently pulling them from the spigots. Once 

removed, be sure to store wear rings in a safe place.

FRONT COVER WEAR RINGS

ROTOR WEAR RINGS

FOODFIRST ROTORS

FOODFIRST FRONT COVER

ROTOR HOUSING

fig. 4.4.1

FRONT COVER WEAR RINGS

FOODFIRST FRONT COVER

fig. 4.4.2

FRONT COVER WEAR RINGS

FOODFIRST FRONT COVER (HP)

SPIGOTS

fig. 4.4.3

Summary of Contents for PD600
























































Reviews:

No comments