manualshive.com logo in svg

UNIBLOC PD600, Operation & Service Manual, Page: 49 / 55

Share
Download
UNIBLOC PD600 Operation & Service Manual Download Page 49

UNIBLOC-PD Operation & Service Manual: PD600-677  49

1

2

5

ITEM NO.

DESCRIPTION

PART NO.

1

2

2

1

2

1

5

REV. NO.

ANGULAR 0.0°   ± 0.1° 0.00°  ± 0.05°

DECIMALS 0.0   ± 0.1 0.00  ± 0.05 0.000 ± 0.005

UNLESS OTHERWISE NOTED:

TOLERANCES

 G2-803

602 SRS

(UNLESS NOTED ON DWG.)

FINISH

MATERIAL

WEIGHT

RELEASE DATE

SHEET 1 OF 2

DWG. NO.

SIZE

DWG. TITLE

 

 DOUBLE O-RING SEAL

MAR. 17, 2017

ALL DIMENSIONS IN MM

DRAWN

CHECKED

APP'D

SCALE

DATE

BY

KL

6/15/11

 2

   

 

THIS DRAWING AND ALL IDEAS INCORPORATED IN ITS  DESIGN IS THE EXCLUSIVE PROPERTY OF UNIBLOC  HYGIENIC TECHNOLOGIES, LLC.  ITS ACCEPTANCE  CONSTITUTES AN AGREEMENT THAT IT SHALL BE TREATED  AS A CONFIDENTIAL DOCUMENT USED FOR NO OTHER  PURPOSE THAN TO AID IN ITS CONSTRUCTION, THAT IT IS  TO BE RETURNED UPON REQUEST, AND THAT IT IS NOT TO  BE DISCLOSED OR COPIED EXCEPT AS AUTHORIZED IN  WRITING BY UNIBLOC HYGIENIC TECHNOLOGIES, LLC.

Summary of Contents for PD600
























































Reviews:

No comments