UNIBLOC PD600 Operation & Service Manual Download Page 32

Page: 32 / 55

32 UNIBLOC-PD Operation & Service Manual: PD600-677

6.2 Lubricants and Bearing Housing Oil Specification

UNIBLOC-PD pumps are factory shipped with Lubriplate

SFGO Ultra-150 PAO-Based Synthetic Food Machinery

Grade Fluid. This lubricant meets FDA 21 CFR 178.3570 and FDA 21 CFR 172.882 and has a temperature rating of

-42°C (-43°F) to 257°C (495°F). The following is a list of other synthetic lubricants that may be used.

Before checking the oil levels

DISENGAGE THE POWER SUPPLY TO THE MOTOR

To check the oil in the bearing housing the pump must first be stopped. Once the oil settles, it should be visible in the

gearbox sightglasses. If not, remove the vents and add oil until visible in the sightglass. If the gearbox does not have

sightglasses, remove the oil level check plug. If oil does not come out of these holes, it must be added through the

vent holes until it starts to do so. Reattach the vents and oil plugs and resume operation.

RECOMMENDED LUBRICANTS

MANUFACTURER

LUBRICANT NAME

TEMP. RANGE,

C (

Mobile

SHC 627

SHC 634

-23...121 (-10...250)

121...152 (250...305)

xxon

partan EP 100

Spartan EP 150

-23...121 (-10...250)

121...152 (250...305)

Shell

pirax S 75W90

-23...152 (-10...305)

Sentinel

S140

-26...288 (-15...550)

BEARING HOUSING CAPACITY

4.5 LITERS

VENT

(OPTIONAL)

SIGHTGLASS

OIL DRAIN PLUG

SIGHTGLASS

VENT

(OPTIONAL)

Horizontal Ports

Vertical Ports

Summary of Contents for PD600
























































Search results

Summary of Contents for PD600

Reviews:

UNIBLOC PD600, Operation & Service Manual, Page: 32 / 55

Search results

Summary of Contents for PD600

Reviews: