manualshive.com logo in svg

UNIBLOC PD600, Operation & Service Manual, Page: 52 / 55

Share
Download
UNIBLOC PD600 Operation & Service Manual Download Page 52

52  UNIBLOC-PD Operation & Service Manual: PD600-677

1

5

6

3

2

4

10

9

8

7

5

11

ITEM NO.

PART NUMBER

DESCRIPTION

QTY.

1

THP-M20

THREADED HINGE PIN

1

2

SA3242-2

LONG ARM

1

3

SA3242-13

HINGE PIN

1

4

SA3242-3 

SHORT ARM

1

5

94751A785

RETAINING RING

2

6

98126A855

WASHER

1

7

SAH3242-5

COVER BRACKET

1

8

WM10x18

M10 WASHER

6

9

LWM10

M10 SPLIT WASHER

6

10

SBM10x25

SOCKET HEAD BOLT: M10x25

6

11

REF. TABLE 2

---

-

TABLE 2

COVER PART NO.

ASS. ASSEM. NO.

DESCRIPTION

2-3241BSAHC-1L

---

PD602 HP FRONT COVER: HOR. SWING ARM

2-3242BSAHC-1L

2-3242BSAH-1L

PD652/677 HP FRONT COVER: HOR. SWING ARM

2-3241BFFSAHC-1L

2-3241BFFSAH-1L

PD602 FF FRONT COVER: HOR. SWING ARM

2-3242BFFSAHC-1L

2-3242BFFSAH-1L

PD652/677 FF FRONT COVER: HOR. SWING ARM

BY

SCALE

APP'D

CHECKED

DRAWN

DATE

ALL DIMENSIONS IN MM, [IN]

SHEET 1 OF 2

DWG. NO.

05/03/19

JH

2-3241SAH-42SAH

1

REV. NO.

FEB. 22, 2021

HORIZONTAL SWING ARM ASSEMBLY 

602SRS 

SIZE

RELEASE DATE 

DWG. TITLE

THIS DRAWING AND ALL IDEAS INCORPORATED IN ITS  DESIGN IS THE EXCLUSIVE PROPERTY OF UNIBLOC  HYGIENIC TECHNOLOGIES, LLC.  ITS ACCEPTANCE  CONSTITUTES AN AGREEMENT THAT IT SHALL BE TREATED  AS A CONFIDENTIAL DOCUMENT USED FOR NO OTHER  PURPOSE THAN TO AID IN ITS CONSTRUCTION, THAT IT IS  TO BE RETURNED UPON REQUEST, AND THAT IT IS NOT TO  BE DISCLOSED OR COPIED EXCEPT AS AUTHORIZED IN  WRITING BY UNIBLOC HYGIENIC TECHNOLOGIES, LLC.

Summary of Contents for PD600
























































Reviews:

No comments