UNIBLOC PD600 Operation & Service Manual Download Page 14

Page: 14 / 55

14 UNIBLOC-PD Operation & Service Manual: PD600-677

ROTOR BOLT WASHERS

ROTOR BOLTS

(1 or 3 Bolts Per Rotor)

LOCK WASHERS

ROTOR BOLT O-RINGS

ROTOR BOLT WASHER O-RINGS

ROTOR HOUSING

ROTORS

fig. 4.3

QuickStrip

ROTORS

SHAFTS

ROTOR HOUSING

fig. 4.2

ROTOR LOCKING NUTS

ROTOR BOLTS

ROTOR BOLT O-RINGS

ROTOR LOCKING NUT O-RINGS

ROTOR HOUSING

ROTORS

fig. 4.4

4.4.1.2 Rotor Removal- QuickStrip

Rotors

QuickStrip

Rotors

do not require locking mechanisms and can simply be removed from the rotor housing by sliding

them off the shafts. Be sure to place the rotors in a safe place while maintenancing the pump, as they can be easily
damaged. Proceed to the respective shaft seal maintenance section once the rotors have been removed

(see fig.4.2)

4.4.1.3 Rotor Removal- Stainless Steel Rotors

If the pump has

Stainless Steel Rotors

, place a nonmetal object (e.g. screwdriver handle) between the rotors to

keep them from turning before removing rotor bolts.

4.4.1.3.1 Three-Bolt Style Shafts

move the six

Rotor Bolts, Rotor Bolt O-rings

Rotor Bolt Washers,

and

Rotor Bolt Washer O-rings.

Slide the

Rotors

off the

Shafts

. If the rotors will not slide off they can be removed simultaneously with the

Rotor Housing

Unless they are being replaced,

DO NOT USE PLIERS OR CHANNEL LOCKS TO REMOVE THE ROTORS. THEY

WILL BE DAMAGED.

Be sure to place the rotors in a safe place while maintenancing the pump as they can be easi

ly damaged

(see fig. 4.3)

4.4.1.3.2 Single-Bolt Style Shafts

(602, 652 & 677 models only)

move the two

Rotor Bolts

(requires special tool, P.N. 6007-2, see section 6.3.2)

, Rotor Locking Nuts and

O-rings.

Slide the

Rotors

off the

Shafts

. If the rotors will not slide off they can be removed simultaneously with the

Rotor Housing

. Unless they are being replaced,

DO NOT USE PLIERS OR CHANNEL LOCKS TO REMOVE THE

ROTORS. THEY WILL BE DAMAGED.

Be sure to place the rotors in a safe place while maintenancing the pump as

they can be easily damaged

(see fig. 4.4)

Summary of Contents for PD600
























































Search results

Summary of Contents for PD600

Reviews:

UNIBLOC PD600, Operation & Service Manual, Page: 14 / 55

Search results

Summary of Contents for PD600

Reviews: