manualshive.com logo in svg

UNIBLOC PD600, Operation & Service Manual, Page: 18 / 55

Share
Download
UNIBLOC PD600 Operation & Service Manual Download Page 18

18  UNIBLOC-PD Operation & Service Manual: PD600-677

ROTATING SEAL FACES

ROTORS & PINS

ROTATING SEAL O-RINGS

STATIONARY SEAL FACES

ROTOR HOUSING

SHAFTS

BEARING HOUSING

STATIONARY SEAL O-RINGS

STATIONARY SEAL FACE HOLDERS

STATIONARY SEAL FACE HOLDER O-RINGS

REAR VEW- ROTOR HOUSING

FRONT VEW- ROTOR & BEARING HOUSING

RETAINING RINGS

REAR ROTOR HOUSING STUD NUTS

fig. 4.6

4.4.2.2.1 Single Mechanical Seal Removal- MODELS: PD602, PD652, PD677

(reference figs. 4.1 , 4.6)

Slide the stainless steel 

Rotors

 off the shafts. If the rotors will not slide off they can be removed simultaneously with 

the 

Rotor Housing

. Unless they are being replaced, 

DO NOT USE PLIERS OR CHANNEL LOCKS TO REMOVE 

THE ROTORS. THEY WILL BE DAMAGED.

 The 

Rotating Seal Faces

, 

Pins

, and 

Rotating Seal O-rings

 are 

assembled inside the 

Rotors

 and will slide out with them. Slide the 

Stationary Seal Face

, 

Stationary Seal O-rings

, 

and  

Stationary Seal Holders 

out of the housing. To avoid damage, handle and store the loose 

Rotating Seal Faces

 

and the 

Stationary Seal Faces

 so that their lapped sealing surfaces do not get scratched. If servicing the 

Bearing 

Housing

, remove the 

Rotor Housing

 by first loosening the 

Rear Rotor Housing Stud Nuts

. Use a hoist and eye bolt 

to support the 

Rotor Housing

. Tap on the ports with a rubber mallet and pull the 

Rotor Housing

 off. Unless being 

serviced, the 

Retaining Rings

 may remain attached to the 

Rotor Housing

.

 

4.4.2.2.2 Single Mechanical Seal Installation- MODELS: PD602, PD652, PD677

(reference figs. 4.1, 4.6, 4.15)

Clean all components prior to installing the seals. If the 

Rotor Housing

 was removed, attach it to the 

Bearing Hous-

ing

 first. Make sure 

Retaining Rings

 are attached to the 

Rotor Housing

.  Using an eye bolt, hoist the rotor hous

-

ing on the 

Dowel Pins

 (see fig. 4.15 on pg. 24) and slide it on, while at the same time threading on the 

Rear Rotor 

Housing Stud Nuts

. Tap the 

Rotor Housing

 with a rubber mallet to seat it properly against the Bearing Housing. 

Tighten the 

Rear Rotor Housing Stud Nuts

 in a cross pattern. Place the 

Stationary Seal Faces

 against the 

Station-

ary Seal Face Holders

 so that the pins slide into the slots. Moisten the 

Stationary Seal Face Holder O-Rings

 with 

water or coat them with a lubricant that is acceptable for contact with the product. Slide these components in the rotor 

housing bores. If removed from the rotors, lubricate 

Rotating Seal O-rings

 and slide them in the rotors together with 

the 

Rotating Seal Faces

 locating them on the seal pocket

 Pins 

on the back side of the the 

Rotors

. The 

Rotating 

Seal Faces

 must be pressed in evenly so that the 

Rotating Seal O-rings

 do not come off. They have been installed 

correctly if they do not fall out when tilting the rotors. Do not use objects that will scratch the 

Rotating Seal Faces’

 

surface to push them in. Place a product compatible lubricant on the sealing surfaces of the 

Stationary Seal Faces

 

and 

Rotating Seal Faces

. Slide the 

Rotors

 on the 

Shafts

. Proceed to section 4.4.6

 

to complete the installation.

Summary of Contents for PD600
























































Reviews:

No comments