manualshive.com logo in svg

UNIBLOC PD600, Operation & Service Manual, Page: 53 / 55

Share
Download
UNIBLOC PD600 Operation & Service Manual Download Page 53

UNIBLOC-PD Operation & Service Manual: PD600-677  53

13

4

3

2

1

7

8

6

7

8

6

7

8

6

7

8

6

10

11

12

10

11

12

10

11

12

10

11

12

9

11

12

9

11

12

9

11

12

13

13

5

9

11

12

9

11

12

9

11

12

14

ITEM NO.

PART NUMBER

DESCRIPTION

QTY.

1

SAV3242-1

MOUNTING BRACKET

1

2

SA3242-2

LONG ARM

1

3

SA3242-3 

SHORT ARM

1

4

SAV3242-4

COVER BRACKET HINGE

1

5

SAV3242-5

COVER BRACKET

1

6

WM20

M20 WASHER

4

7

HBM20x45

M20x45 HEX HEAD BOLT

4

8

LWM20

M20 SPLIT WASHER

4

9

HBM10x25

M10x25 HEX BOLT 

6

10

SBM10x20

M10x20 SOCKET HEAD BOLT

4

11

LWM10

M10 SPLIT WASHER

10

12

WM10x18

M10 WASHER

10

13

SA3242-13

HINGE PIN

3

2-3241BSAVC-1L

PD602 HP FRONT COVER FOR VERT. SWING ARM

2-3242BSAVC-1L

PD652/677 HP FRONT COVER FOR VERT. SWING ARM

2-3241BFFSAVC-1L

PD602 FOODFIRST FRONT COVER FOR VERT. SWING ARM

2-3242BFFSAVC-1L

PD652/677 FOODFIRST FRONT COVER FOR VERT. SWING ARM

PART NO.

DESCRIPTION

ASSOCIATED PARTS

BY

SCALE

APP'D

CHECKED

DRAWN

DATE

ALL DIMENSIONS IN MM, [IN]

SHEET 1 OF 2

DWG. NO.

KL

SAV32

5

REV. NO.

JAN. 18, 2022

VERTICAL SWING ARM ASSEMBLY

602SRS

SIZE

RELEASE DATE 

DWG. TITLE

WEIGHT

FINISH 

(UNLESS NOTED ON DWG.)

MATERIAL

ANGULAR 0.0°   ± 0.1° 0.00°  ± 0.05°

DECIMALS 0.0   ± 0.1 0.00  ± 0.05 0.000 ± 0.005

UNLESS OTHERWISE NOTED

TOLERANCES

5/16/19

 

THIS DRAWING AND ALL IDEAS INCORPORATED IN ITS  DESIGN IS THE EXCLUSIVE PROPERTY OF UNIBLOC  HYGIENIC TECHNOLOGIES, LLC.  ITS ACCEPTANCE  CONSTITUTES AN AGREEMENT THAT IT SHALL BE TREATED  AS A CONFIDENTIAL DOCUMENT USED FOR NO OTHER  PURPOSE THAN TO AID IN ITS CONSTRUCTION, THAT IT IS  TO BE RETURNED UPON REQUEST, AND THAT IT IS NOT TO  BE DISCLOSED OR COPIED EXCEPT AS AUTHORIZED IN  WRITING BY UNIBLOC HYGIENIC TECHNOLOGIES, LLC.

Summary of Contents for PD600
























































Reviews:

No comments