manualshive.com logo in svg

UNAOHM AP 401 Full HD, User Manual

Share
Download
UNAOHM AP 401 Full HD User Manual Download Page 29

 

AP401FULL- HD_rev. 09_UK 

28 

 

Tuning can only be carried out by setting the frequency of the transponder in one of the 

following manners (it is not possible to use the 1

st

 IF frequency): 

1) Using the numeric keyboard and pressing the 

ENTER

 button to confirm. 

2) Turning the shaft encoder until the display shows the desired frequency. 
The possible frequency settings (0.1 MHz or 4.0 MHz) can be selected by holding down the 

FR 

button and turning the shaft encoder to set the frequency cursor to the number that 

corresponds to the whole number or decimal. Press 

ENTER

 to confirm the selection. 

 

During functionality in SCR mode, the following functions remain enabled: 

-

 

The normal spectrum analyzer functions.  

-

 

LNB: enables or disables the power supply voltage of the SCR LNB.  

-

 

TV: for viewing analogue or digital images by means of MPEG4 / MPEG2 decoding. 

-

 

MEA: allows for switching to MEASUREMENT mode.  

-

 

DIGI: Allows the QPSK card to be activated in order to analyze the quality of the 
digital satellite signal with the relative BER, PVBER and MER readings, as well as that 

of other parameters. The possibility of activating the MPEG4/MPEG2 card also 
provides for the reading of the NIT and the viewing of the images from the free-to-

air digital channels.  

Press the 

DSQ

 button to exit SCR mode: the SCR function will be deactivated and the 

instrument will return to the main screen. 

4.14.

 

SOUND 

4.14.1.

 

FOR TERRESTRIAL CHANNELS 

The instrument is equipped with three audio demodulators that are automatically selected 

by the instrument based on the type of measurement demodulator in use. 
TV  For television signals, the relative audio subcarrier frequency (5.5-6-6.5 MHz) and the 

type of modulation (normally FM and AM for the L standard) are automatically selected 
based on the set standard. 

FM  For frequency modulated carriers (for example, FM radio stations) FM demodulator.  

AM  For amplitude modulated carriers (for example, remote controls) AM demodulator.  

4.14.2.

 

FOR SATELLITE CHANNELS 

Press the 

2nd

 and 

Sound

 buttons to display the menu regarding the preset or custom 

audio subcarrier settings. In order to select the desired audio, turn the dial to bring the 

cursor to the selected position and press 

ENTER

. The menu items include the following: 

z

 

DEFAULT SOUND: select this item to select the desired audio subcarrier from amongst 
those present within the table. 

z

 

CUSTOM SOUND: allows for four audio subcarriers to be freely configured and listed 
along with the predefined standard ones. In order to carry out the configuration: 

•

 

Select CUSTOM SOUND and press 

ENTER

. 

•

 

Select the subcarrier to be configured and press 

ENTER

. 

•

 

Turn the Shaft Encoder to set the desired frequency and press 

ENTER 

to confirm. Press 

the 

SOUND 

button to exit. 

 

 

Summary of Contents for AP 401 Full HD



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands