UNAOHM AP 401 Full HD User Manual Download

Page: 19 / 58

AP401FULL- HD_rev. 09_UK

4.5.2.

USING THE LOCAL OSCILLATORS (LO)

By repeatedly pressing the

LO (4)

button, depending on the settings inserted within the

menu, the satellite frequency will be displayed as follows:

FOR THE “DEFAULT LO” SETTING:

•

IF: 1

IF frequency is displayed

•

LO 1: the tuned frequency in relation to the 9750 MHz oscillator is displayed.

•

LO 2: the tuned frequency in relation to the 10600 MHz oscillator is displayed.

FOR THE “USER LO” SETTING:

•

IF: 1

IF frequency is displayed

•

LO 1: the tuned frequency in relation to the set local oscillator is displayed.

•

LO 2: the tuned frequency in relation to the set local oscillator is displayed.

•

LO 3: the tuned frequency in relation to the set local oscillator is displayed.

•

LO 4: the tuned frequency in relation to the set local oscillator is displayed.

4.5.2.1.

VERIFICATION OF THE CHANNELING SYSTEM IN USE

Hold down the

button to access the menu on the display and verify the channeling

system is use under the “CHANNEL TABLE” item.

4.6.

FREQUENCY / CHANNEL STORAGE

In order to store a frequency or channel in one of the 100 available program memory slots,

proceed in the following manner:
I.

Insert the number of the program in which you would like to store the frequency (or

channel).

II.

Insert the frequency (or channel).

III.

Press the “

2nd

” button and then the

STORE

button.

IV.

Use the same procedure to store any other desired programs.

WARNING! If the LNB power supply is connected while the storage procedure is

being carried out, it will be applied by directly calling up a program.

⇒

NOTE

In order to store a channel, the procedure requires not only the acquisition of the

video/audio carriers, but also other parameters such as “BW” (bandwidth) and “STD”

(TV-standard). Therefore, when a program with SAT frequencies is called up, its audio
and video will also be presented: it is therefore recommended to tune the desired audio

subcarrier before storing a SAT channel.

4.6.1.

PROGRAM (PR) MENU

Hold down the

PR STORE

button to access the menu for inspecting/modifying the stored

programs. When finished, press the

PR STORE

button again to exit the menu.

Summary of Contents for AP 401 Full HD



























































Search results

Summary of Contents for AP 401 Full HD

Reviews:

Related manuals for AP 401 Full HD

Brands by name

Popular brands

UNAOHM AP 401 Full HD, User Manual

Search results

Summary of Contents for AP 401 Full HD

Reviews:

Related manuals for AP 401 Full HD

Brands by name

Popular brands