D2. OPTIONAL MAGNA PAD
1. If applicable, clean the Magnepad envelope filter pad at CLOSING as follows: Remove and discard the used filter pad
envelope, carefully clean the baffle assembly and clip/standpipe assembly in a 3 compartment sink with hot water and
allow these items to air dry. DO NOT USE SOAP!! Reassemble the Magnepad envelope filter using a NEW Magnesol
Impregnated Filter Pad or paper envelope as follows:
a. Insert the BAFFLE into the FILTER PAD ENVELOPE, when properly inserted, the SUCTION FITTING will pro-
trude through the hole in the pad.
b. Fold the FLAP over (in the direction of the hole) securing the Baffle inside the FILTER PAD ENVELOPE.
c. CAREFULLY align the CLIP & STANDPIPE ASSEMBLY so that the clip can secure the FLAP and the envelope
and the STANDPIPE will align over the SUCTION FITTING protruding through the envelope.
d. Tighten the knurled NUT on the STANDPIPE to the SUCTION FITTING protruding through the envelope.
e. Repeat DAILY steps 1 a through 1 d .
E. REASSEMBLE
1. CAREFULLY insert the assembled Filter Screen in the bottom of the Filter Tub; then CAREFULLY insert the Crumb
Catcher Pan in the Filter Tub with the DRAIN VALVE Docking Flange over the leading edge of the pan.
2. CAREFULLY position the FILTER TUB COVER on the OPEN end of the Filter Tub with the SLOT on the cover seated
around the Standpipe Handle Docking Assembly. Then, SECURE the cover to the standpipe assembly by locking the
latch on the cover.
3. Position the ASSEMBLED Filter Tub in front of the FILTER TUB GUIDES beneath the fryer; then CAREFULLY and
SLOWLY insert the Filter Tub into the fryer using the Standpipe Docking Handle until the MALE In Line Plug on the
Standpipe Docking Handle Assembly seats in the FEMALE Bulkhead Coupling adjacent to the Drain Valve Assembly
II. WEEKLY
A. Perform daily cleaning steps B through D.
B. Boilout fryer. If using mesh screen place the upper and lower FILTER SCREENS in the fryer with BOIL-OUT SOLU-
TION for cleaning. BOIL-OUT the fryer vat according to instructions contained in the cleaning manual provided by your
chemical supplier.
C. After the filter screens have been cleaned in the Boil-Out Solution, ENSURE they are THOROUGHLY sprayed with a
solution of 1 PART vinegar to 25 PARTS of water to NEUTRALIZE the boil-out solution, then allow the screens to air
dry. NOTE: any residue of boil-out solution on the filter screens could cause the rapid break-down of the shortening.
D. Reassemble the “Micro-Mesh stainless steel filter according to DAILY steps D1f through D1.
E. Place the CRUMB CATCHER PAN and SLUDGE CATCHER SCREEN in the fryer with the Boil-Out Solution for
cleaning, and after they are cleaned, ENSURE they are sprayed with a solution of vinegar/water as described in
WEEKLY above.
F. THROUGHLY clean the Filter Tub, Cover and Sludge Catcher Pan with HOT SANITIZER SOLUTION and allow them
to air dry.
G. Re-assemble and install the Filter Tub according to the FILTER TUB ASSEMBLY AND INSTALLATION section of
this manual.
CAUTION:
WHEN ASSEMBLED, ENSURE THERE ARE NO FINGER LOOPS ON THE STANDPIPE SIDE OF THE
FILTER.
Page 17
30A134
CAUTION:
DO NOT PLACE THE BAFFLE OR STANDPIPE IN THIS SOLUTION!!!
Summary of Contents for PAR-3-14HE CE
