TRONTEQ Electronic Qiwi Lite User Manual Download Page 9

Page: 9 / 31

User Manual Qiwi Lite
Support: www.tronteq.de/support
Release 11/2016

Seite 9 von 31

3.2.

Connecting the power supply

DANGER!

Never perform wiring electrical connections if they are under voltage!

Assignment Connection

Image

Power supply 1, plus pole

GND

Power supply 1 and 2, minus pole

FAULT

Fault Contact

DI+

Digital Input plus pole

DI-

Digital Input minus pole

FAULT

Fault Contact

GND

Power supply 1 and 2, minus pole

Power supply 2, plus pole

3.3.

Connecting the Fault Contact

See chapter 3.2.

3.4.

Connecting the Digital Input

See chapter 3.2.

3.5.

Connecting the USB flash drive

The connection is performed with the USB-A port of the device.

Assignment Connection

Image

VBUS

+5V

D-

Data -

D+

Data +

GND

Ground (not connected with shielding)

3.6.

Connecting the Ethernet ports

The connection is performed with the RJ-45 jacks (8P8C) of the device.

Assignment Connection

Image

TX+

Data TX+

TX-

Data TX-

RX+

Data RX+

Not connected

RX-

Data RX-

Not connected

Summary of Contents for Qiwi Lite
































Search results

Summary of Contents for Qiwi Lite

Reviews:

Related manuals for Qiwi Lite

Brands by name

Popular brands

TRONTEQ Electronic Qiwi Lite, User Manual

Search results

Summary of Contents for Qiwi Lite

Reviews:

Related manuals for Qiwi Lite

Brands by name

Popular brands