TRONTEQ Electronic Qiwi Lite User Manual Download Page 10

Page: 10 / 31

User Manual Qiwi Lite
Support: www.tronteq.de/support
Release 11/2016

Seite 10 von 31

First start-up

4.1.

Default Settings

The device is delivered pre-configured. The factory configuration is set as follows: after powering the
Switch, the device sends data to all Ethernet ports immediately. The following settings are set at the
factory:

► Web interface IP address:

192.168.0.2

► Web interface user name:

admin

► Web interface password:

password

► Web interface access:

port 1-6

► Ethernet ports:

activated

► Auto-Negotiation

activated

► VLAN, QoS, Port Mirroring:

deactivated

► Link Aggregation:

deactivated

► Fault Contact:

Normally Open

► Fault Contact Events:

V1 or V2 fault; over temperature

► TRAP protocol :

UDP

► TRAP IP address:

192.168.0.1:4321

► TRAP events:

V1 or V2 fault; over temperature, internal fault

► Logging function:

activated

4.2.

First operation

Proceed as follows for the first operation:

1. Connect the power supply

2. Connect the PC / notebook to one of the Ethernet ports 1-8 of the device

3. The connected PC / laptop must have the following network settings:

► Configured IP-Address:

192.168.0.1

► Subnet mask:

255.255.255.0

4. Start the web browser and enter the LAN-IP address of the device

5. Perform the desired configuration of the device

6. Connect the switch with your network devices

Summary of Contents for Qiwi Lite
































Search results

Summary of Contents for Qiwi Lite

Reviews:

Related manuals for Qiwi Lite

Brands by name

Popular brands

TRONTEQ Electronic Qiwi Lite, User Manual

Search results

Summary of Contents for Qiwi Lite

Reviews:

Related manuals for Qiwi Lite

Brands by name

Popular brands