TRONTEQ Electronic Qiwi Lite User Manual Download Page 20 | Manualshive

Page: 20 / 31

background image

User Manual Qiwi Lite
Support: www.tronteq.de/support
Release 11/2016

Seite 20 von 31

7.4.

TRAP

Traps are used to signalizing of fault status of the device. Traps are data packets that are sent to a
configured network address. With the defined network address a monitoring of the device is possible.

The content of the data packet consists of two bytes which contains the current fault status.

In the web interface the following configurations can be made at

Configuration > System

:

► Traps activate / deactivate (default: activated)

► Protocol: TCP, UDP (default: UDP)

► Target-IP-address (default: 192.168.0.1)

► Target-port: (default: 4321)

As trigger for Traps one or several of the following fault statuses can be configured:

► Power (active as default)

► Temperature (active as default)

► Linkdown (active as default)

► Internal (active as default)

► Digital Input

«
...
18
19
20
21
22
...
»

Summary of Contents for Qiwi Lite
































Reviews:

No comments

Related manuals for Qiwi Lite

All in One Printer

Brand: Baracoda Pages: 42

Brand: D-Link Pages: 4

Brand: D-Link Pages: 2

Brand: D-Link Pages: 9

Brand: D-Link Pages: 8

Brand: D-Link Pages: 3

Brand: D-Link Pages: 28

Brand: D-Link Pages: 2

DSL-2540B - ADSL2/2+ Modem With EN Router

Brand: D-Link Pages: 12

Brand: D-Link Pages: 62

Brand: Niveo Pages: 155

Brand: Premio Pages: 3

Brand: CSS Pages: 2

Brand: Direct IP Pages: 76

Brand: XtendLan Pages: 228

Brand: WABCO Pages: 29

DataPlot CB1224

Brand: B-G Instruments Pages: 4

Brand: BHU NETWORKS Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands