TRONTEQ Electronic Qiwi Lite User Manual Download Page 8 | Manualshive

Page: 8 / 31

background image

User Manual Qiwi Lite
Support: www.tronteq.de/support
Release 11/2016

Seite 8 von 31

2.4.

Interfaces

Below is a picture of the Qiwi Lite Switch

Digit

Description

1

System-LEDs: PWR = Power, MOD = Mode, ERR = Error, DI = Digital Input

2

Connection for power supply, fault contact, Digital Input

3

USB Port

4

Ethernet Port with Port-LEDs: LA = Link, SP = Speed

5

Ground connection

3.

Installation

WARNING!

Never perform wiring electrical connections if they are under voltage!

Do not perform any assembly work on the device when it is under voltage

3.1.

Mounting

Perform the following steps for mounting the device:

► Make sure that all electrical connectors are volt-free

► Make sure that the device is disconnected from all connections

► Mount the device on a DIN rail

► Mount the device on a flat surface with four M4 screws

► Ground the device with the provided ground connection

Make sure that the ground connection is always tightened securely. Use
toothed lock washers with internal teeth to produce ideal contact.

1

3

2

4

5

«
...
6
7
8
9
10
...
»

Summary of Contents for Qiwi Lite
































Reviews:

No comments

Related manuals for Qiwi Lite

Brand: Patton electronics Pages: 2

ipRocketLink 3086FR

Brand: Patton electronics Pages: 6

Brand: Patton electronics Pages: 16

Brand: Patton electronics Pages: 51

Brand: Danfoss Pages: 61

Brand: YASKAWA Pages: 68

Brand: Fortinet Pages: 20

Brand: Belkin Pages: 72

Brand: Helmholz Pages: 28

HiGain HLU-231 List 8F

Brand: ADC Pages: 7

Brand: Allied Telesis Pages: 22

Brand: Watchguard Pages: 40

TE100-S16 - 10/100Mbps Ethernet Switch

Brand: TRENDnet Pages: 15

Brand: Idis Pages: 85

Brand: THOMSON Pages: 212

Brand: Galaxy Pages: 30

Brand: Teletronics International Pages: 57

NetVanta Analog Modem Dial Backup Interface Module

Brand: ADTRAN Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands