manualshive.com logo in svg

Triumph Adler DP 773, Service Manual

Share
Download
Triumph Adler DP 773 Service Manual Download Page 75

3PH

1-4-6

1-4-3  Electric problems

If the part causing the problem was not supplied, use the unit including the part for replacement.
Troubleshooting to each failure must be in the order of the numbered symptoms.

Problem

Causes

Check procedures/corrective measures

(1)
The LED lamp 
does not turn on  
when original is 
present on the DP.

1. Defective connector 

cable or poor con-
tact in the connector.

Reinsert the connector. Also check for continuity within the 
connector cable. If none, replace the cable.
DP original sensor and DP main PWB (YC3)
DP main PWB (YC1) and engine PWB (YC18)

2. Defective sensor.

Replace the DP original sensor.

3. Defective PWB.

Replace the DPLED PWB or the DP main PWB and check 
for correct operation (see page 1-5-5).

(2)
The size of original 
on the DP is not 
displayed correctly.

1. Defective connector 

cable or poor con-
tact in the connector.

Reinsert the connector. Also check for continuity within the 
connector cable. If none, replace the cable.
DP original size width sensor and DP main PWB (YC4)
DP original size length sensor and DP main PWB (YC2)
DP main PWB (YC1) and engine PWB (YC18)

2. Defective sensor.

Replace the DP original size width sensor or DP original 
size length sensor.

3. Defective PWB.

Replace the DP main PWB or engine PWB and check for 
correct operation (see page 1-5-5).

(3)
DP paper feed 
motor does not 
operate.

1. Defective connector 

cable or poor con-
tact in the connector.

Reinsert the connector. Also check for continuity within the 
connector cable. If none, replace the cable.
DP paper feed motor and DP main PWB (YC9)
DP main PWB (YC1) and engine PWB (YC18)

2. Defective drive trans-

mission system.

Check if the rollers and gears rotate smoothly. If not, 
grease the bushes and gears. Check for broken gears and 
replace if any.

3. Defective motor.

Replace the DP paper feed motor.

4. Defective PWB.

Replace the DP main PWB or engine PWB and check for 
correct operation (see page 1-5-5).

(4)
DP switchback 
motor does not 
operate.

1. Defective connector 

cable or poor con-
tact in the connector.

Reinsert the connector. Also check for continuity within the 
connector cable. If none, replace the cable.
DP switchback motor and DP main PWB (YC9)
DP main PWB (YC1) and engine PWB (YC18)

2. Defective drive trans-

mission system.

Check if the rollers and gears rotate smoothly. If not, 
grease the bushes and gears. Check for broken gears and 
replace if any.

3. Defective motor.

Replace the DP switchback motor.

4. Defective PWB.

Replace the DP main PWB or engine PWB and check for 
correct operation (see page 1-5-5).

Summary of Contents for DP 773


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands