manualshive.com logo in svg

Triumph Adler DP 773, Service Manual

Share
Download
Triumph Adler DP 773 Service Manual Download Page 61

3PH

1-3-41

U411

* : When automatic adjustment has normally completed, [OK] is displayed. If a problem 

occurs during auto adjustment, error code is displayed and operation stops. Should this 
happen, determine the details of the problem and repeat the procedure from the begin-
ning.

Method: [DP Auto Adj]

1. Load A4/letter paper.
2. Press the start key to output the original for adjustment.
3. Set the output the original for adjustment and press the start key.
4. Set the output the original for adjustment on the DP face up.
5. Press the start key to scan documents.
6. Press the start key. Auto adjustment of first side starts.
7. Set the output the original for adjustment on the DP face down.
8. Press the start key to scan documents.
9. Press the start key. Auto adjustment of second side starts.

* : When automatic adjustment has normally completed, [OK] is displayed. If a problem 

occurs during auto adjustment, error code is displayed and operation stops. Should this 
happen, determine the details of the problem and repeat the procedure from the begin-
ning.

Error Codes

Item No.

Description

Codes

Description

01

Black band detection error (scanner auxiliary scanning direction leading edge 
skew )

02

Black band detection error (scanner main scanning direction far end skew)

03

Black band detection error (scanner main scanning direction near end skew)

03

Black band detection error (scanner auxiliary scanning direction trailing edge 
skew)

04

Black band is not detected (scanner auxiliary scanning direction leading edge)

05

Black band is not detected (scanner main scanning direction far end)

06

Black band is not detected (scanner main scanning direction near end)

07

Black band is not detected (scanner auxiliary scanning direction trailing edge)

08

Black band is not detected (DP main scanning direction far end)

09

Black band is not detected (DP main scanning direction near end)

0a

Black band is not detected (DP auxiliary scanning direction leading edge)

0b

Black band is not detected (DP auxiliary scanning direction leading edge origi-
nal check)

0c

Black band is not detected (DP auxiliary scanning direction trailing edge)

0d

White band is not detected (DP auxiliary scanning direction trailing edge)

0e

DMA time out

0f

Auxiliary scanning direction magnification error

10

Auxiliary scanning direction leading edge error

11

Auxiliary scanning direction trailing edge error

Summary of Contents for DP 773


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands