manualshive.com logo in svg

Triumph Adler DP 773, Service Manual

Share
Download
Triumph Adler DP 773 Service Manual Download Page 50

3PH

1-3-30

U203

Checking DP operation

Description

Simulates the original conveying operation separately in the DP.

Purpose

To check the DP operation.

Method

1. Press the start key.
2. Place an original in the DP if running this simulation with paper.
3. Select the speed to be operated.

4. Select the item to be operated.

5. Press the start key. The operation starts. 
6. To stop continuous operation, press the stop key. 

Setting: [Mode]

1. Select On or Off.

2. Press the start key. 

Setting: [Reset]

1. Select [Execute].
2. Press the start key. 

Item No.

Description

Display

Description

Normal Speed

Normal reading (600 dpi)

High Speed

High-speed reading

Mode

Sets the conveying timing verification mode

Reset

Resets the conveying timing verification data

Result

Resets the conveying timing verification data

Display

Description

CCD ADP

With paper, single-sided original of CCD

CCD RADP

With paper, double-sided original of CCD

CIS

With paper, double-sided original of CIS

CCD ADP (Non-P)

Without paper, single-sided original of CCD 
(continuous operation)

CCD RADP (Non-P)

Without paper, double-sided original of CCD 
(continuous operation)

CIS (Non-P)

Without paper, double-sided original of CIS 
(continuous operation)

Display

Description

On

Sets the conveying timing verification mode on

Off

Sets the conveying timing verification mode off

Summary of Contents for DP 773


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands