manualshive.com logo in svg

Triumph Adler DP 773, Service Manual

Share
Download
Triumph Adler DP 773 Service Manual Download Page 58

3PH

1-3-38

U411

8. Press the start key. Auto adjustment starts.

* : When automatic adjustment has normally completed, [OK] is displayed. If a problem 

occurs during auto adjustment, error code is displayed and operation stops. Should this 
happen, determine the details of the problem and repeat the procedure from the begin-
ning.

Method: [DP FaceDown (Chart1)]

To manually enter the target value

1. Enter the target values which are shown at the bottom of the specified original 

(P/N: 7505000005) executing maintenance item U425. 

2. Set a specified original on the DP face down.
3. Enter maintenance item U411.
4. Select [Target].
5. Select [U425] and press the start key.
6. Select [DP FaceDown (Chart1)].
7. Select [All].

To automatically enter the target value

1. Enter the value for [Adjust Original] using maintenance item U425. 
2. Set a specified original (P/N: 7505000005) on the DP face down.
3. Enter maintenance item U411.
4. Select [Target].
5. Select [Auto] and press the start key.
6. Select [DP FaceDown (Chart1)].
7. Select [All].

8. Press the start key. Auto adjustment starts.

* : When automatic adjustment has normally completed, [OK] is displayed. If a problem 

occurs during auto adjustment, error code is displayed and operation stops. Should this 
happen, determine the details of the problem and repeat the procedure from the begin-
ning.

Item No.

Description

Display

Description

Input

Executing the adjustment for input gamma and matrix

Display

Description

All

Executing the adjustment in the DP scanning section (second 
side) for magnification, leading edge timing, center line, MTF 
filter, input gamma and matrix

Summary of Contents for DP 773


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands