manualshive.com logo in svg

Triumph Adler DP 773, Service Manual

Share
Download
Triumph Adler DP 773 Service Manual Download Page 43

3PH

1-3-23

U071

Adjustment: Leading edge registration

1. Change the setting value using the +/- keys or numeric keys.

For copy example 1, increase the value. For copy example 2, decrease the value.
Increasing the value moves the image forward and decreasing the value moves the image 
backward.

Figure 1-3-6 

2. Press the start key. The value is set.

Adjustment: Trailing edge registration

1. Change the setting value using the +/- keys or numeric keys.

For copy example 1, increase the value. For copy example 2, decrease the value.

Figure 1-3-7 

2. Press the start key. The value is set.

Caution

If the first side is adjusted, check the second side and if adjustment is required, carry out the 
adjustment.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Item No.

Description

Original

Copy

example 1

Copy

example 2

Original

Copy

example 1

Copy

example 2

Summary of Contents for DP 773


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands