Triumph Adler DP 773 Service Manual Download Page 22

Page: 22 / 113

3PH

1-3-2

(2) Maintenance modes item list

Section

Item

No.

Content of maintenance item

Initial setting

General

U000 Outputting an own-status report

U001 Exiting the maintenance mode

U019 Displaying the firrmware version

Optical

U061 Checking the operation of the exposure lamp

U068 Adjusting the scanning position for originals

from the DP

0/0

U070 Adjusting the DP magnification

-/-/-/-

U071 Adjusting the DP scanning timing

-/-/-/-/-/-

U072 Adjusting the DP center line

-/-/-

U073 Checking the scanner operation

100/10200/1

U074 Adjusting the DP input light luminosity

U087 Setting DP reading position modification opera-

tion

145/145/145

U099 Adjusting original size detection

(With original mat)

(With document feeder)

0/0/0/0/0

20/30/40/20/30/40/20/30/40

50/50/50/50/50/50/50/50/50

0/0/0/0/0

Operation

panel and

support

equipment

U203 Checking DP operation

U243 Checking the operation of the DP motors

U244 Checking the DP switches

Mode set-

ting

U326 Setting the black line cleaning indication

ON/8

Image

processing

U404 Adjusting margins for scanning an original from

the DP

3.0/2.5/3.0/4.0

U411

Adjusting the scanner automatically

Summary of Contents for DP 773


















































































































Search results

Summary of Contents for DP 773

Reviews:

Brands by name

Popular brands

Triumph Adler DP 773, Service Manual

Search results

Summary of Contents for DP 773

Reviews:

Brands by name

Popular brands