Triumph Adler DP 773 Service Manual Download Page 44

Page: 44 / 113

3PH

1-3-24

U072

Adjusting the DP center line

Description

Adjusts the scanning start position for the DP original.

Purpose

Perform the adjustment if there is a regular error between the centers of the original and the copy
image when the DP is used.

Adjustment

1. Press the start key.
2. Press the system menu key.
3. Place an original on the DP and press the start key to make a test copy.
4. Press the system menu key.
5. Select the item to be adjusted.l

*: Dual scan DP only

6. Change the setting value using the +/- keys or numeric keys.

For copy example 1, increase the value. For copy example 2, decrease the value.

Figure 1-3-8

7. Press the start key. The value is set.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Item No.

Description

Display

Description

Setting

range

Initial

setting

Change in

value per step

Front

DP center line (first side)

-60 to 60

0.085 mm

Back

DP center line (second side)

-60 to 60

0.085 mm

CIS*

CIS center line

-39 to 39

0.085 mm

Original

Copy

example 1

Copy

example 2

Summary of Contents for DP 773


















































































































Search results

Summary of Contents for DP 773

Reviews:

Brands by name

Popular brands

Triumph Adler DP 773, Service Manual

Search results

Summary of Contents for DP 773

Reviews:

Brands by name

Popular brands