manualshive.com logo in svg

Triumph Adler DP 773, Service Manual

Share
Download
Triumph Adler DP 773 Service Manual Download Page 53

3PH

1-3-33

U244

Checking the DP switches

Description

Displays the status of the respective switches and sensors in the DP.

Purpose

To check if respective switches and sensors in the DP operate correctly.

Method

1. Press the start key.
2. Turn each switch or sensor on and off manually to check the status.

When the on-status of a switch or sensor is detected, that switch or sensor is displayed in 
reverse.

 *1

: DP-770(B)  

*2

:

 

DP-772   

*3

: DP-773

Completion 

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Item No.

Description

Display

Description

Feed

 *1,*2,*3

DP feed sensor (DPFS)

Regist 

*1,*3

DP registration sensor (DPRS)

Timing

 *1,*2,*3

DP timing sensor (DPTS)

CIS Head 

*2

DP CIS sensor (DPCS)

Tray 

*1,*3

DP switchback sensor (DPSBS)

Set

 *1,*2,*3

DP original sensor (DPOS)

Longitudinal

 *1,*2

DP original length switch (DPOLSW)

Lift U-Limit

 *1,*2

DP lift sensor 1 (DPLS1)

Lift L-Limit

 *1,*2

DP lift sensor 2 (DPLS2)

Cover Open

 *1,*2,*3

DP interlock switch (DPILSW)

Open

 *1,*2,*3

DP open/close switch (DPOCSW)

Eject

 *1,*2

DP eject sensor (DPES)

Slant 

*2

DP slant sensor (DPSS)

Summary of Contents for DP 773


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands