manualshive.com logo in svg

Triumph Adler DP 773, Service Manual

Share
Download
Triumph Adler DP 773 Service Manual Download Page 73

3PH

1-4-4

9050

DP lift motor going down 
error

When the DP lift motor is 
driven, DP lift sensor 2 does 
not turn on within 1500 pulse.
(Three recovery times.)
The above has been detected 
5 times.

DP lift motor

1. Execute U906 Separating Operation 

Release.

2. Execute U243 Lift Motor to check the DP 

motor operation (see page 1-3-32).

3. Check that the original document lift 

guide can move downwards.

4. Confirm that the wiring connector is 

firmly connected and, if necessary, 

connect the connector all the way in.

DP lift motor and DP main PWB (YC5)

If the wiring is disconnected, shorted or 

grounded, replace the wiring.

5. Replace the DP lift motor.

DP lift sensor 2

1. Execute U244 LIFT L-Limit to check DP 

switch (see page 1-3-33).

2. Confirm that the DP lift sensor 2 has 

been firmly fitted.

3. Confirm that the wiring connector is 

firmly connected and, if necessary, 

connect the connector all the way in.

DP lift sensor 2 and DP main PWB 

(YC2)

4. Replace the DP lift sensor2.

DP main PWB

Replace the DP main PWB

9060

DP EEPROM error

Mismatch of reading data from 
two locations occurs 3 times 
successively.
Mismatch between writing 
data and reading data occurs 
3 times successively.

DP main PWB

1. Execute U906 Separating Operation 

Release.

2. Confirm that the EEPROM has been 

properly installed.

3. Replace the DP main PWB

Device damage of 
EEPROM

Contact the Service Support.

9070

Communication error 
between DP and SHD

A communication error is 
detected.

DP SHD PWB

1. Execute U906 Separating Operation 

Release.

2. Confirm that the wiring connector is 

firmly connected and, if necessary, 

connect the connector all the way in.

DP SHD PWB (YC1) and DP main PWB 

(YC10)

3. If the wiring is disconnected, shorted or 

grounded, replace the wiring.

4. Replace the DP SHD PWB.

Code

Contents

Causes

Check procedures/

corrective measures

Summary of Contents for DP 773


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands