manualshive.com logo in svg

Triumph Adler DP 773, Service Manual

Share
Download
Triumph Adler DP 773 Service Manual Download Page 52

3PH

1-3-32

U243

Checking the operation of the DP motors

Description

Turns the motors or solenoids in the DP on.

Purpose

To check the operation of the DP motors and solenoids.

Method

1. Press the start key.
2. Select the item to be operated.
3. Press the start key. The operation starts.

 *1

: DP-770(B)  

*2

:

 

DP-772   

*3

: DP-773

4. To turn each motor off, press the stop key.

Completion

Press the stop key when operation stops. The screen for selecting a maintenance item No. is dis-
played.

Item No.

Description

Display

Description

Feed Motor 

*1,*2,*3

DP original feed motor (DPOFM) is turned on

Conv Motor 

*1,*2

DP original conveying motor (DPOCM) is turned on

Rev Motor 

*1,*3

DP switchback motor (DPSBM) is turned on

Lift Motor 

*1,*2

DP lift motor (DPLM) is turned on

Rev Press Sol 

*1

DP pressure solenoid (DPPSOL) is turned on

Rev Branch Sol 

*1

DP feedshift solenoid (DPFSSOL) is turned on

Eject Motor 

*2

DP eject motor (DPEM) is turned on

Regist Motor 

*2

DP registration motor (DPRM) is turned on

DP Fan

*2

DP fan motor 1 (DPFM1) is turned on

CIS Fan

*2

DP fan motor 2 (DPFM2) is turned on

Summary of Contents for DP 773


















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands