Triumph Adler DP 773 Service Manual Download Page 68

Page: 68 / 113

3PH

1-3-48

U905

Checking counts by optional devices

Description

Displays the counts of document processor or document finisher.

Purpose

To check the use of document processor or document finisher.

Method

1. Press the start key.
2. Select the device to be checked. The count of the selected device is displayed.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Item No.

Description

Display

Description

Counts of document processor

Counts of document finisher

Display

Description

ADP

Counts of single-sided originals that has passed through the DP

RADP

Counts of double-sided originals that has passed through the DP

CIS

Counts of Double-sided simultaneous reading originals that has
passed through the DP

Display

Description

Sorter

Counts of copies that has passed through the sorter

Staple

Frequency the stapler has been activated

Summary of Contents for DP 773


















































































































Search results

Summary of Contents for DP 773

Reviews:

Brands by name

Popular brands

Triumph Adler DP 773, Service Manual

Search results

Summary of Contents for DP 773

Reviews:

Brands by name

Popular brands