manualshive.com logo in svg

Tritech SeaHub, Operator'S Manual

Share
Download
Tritech SeaHub Operator'S Manual Download Page 52

 

Operator Manual

 
  

Issue 1 

TIL – Eng – Spec – 080 

Page 52 of 70 

 

SeaHub 

7.4.2. Checking/replacing the DC Main Output Power (+28V Supply) Fuse 

Use this section if there is no +28V (

±

5%) power from either Port C or D, or the 4mm Power Sockets on 

the rear of the unit (assuming the power selection jumpers are set correctly). 
 

9)  Unplug the SeaHub unit from any power sources. 

10) Follow the steps described in section 7.1 to open the 

housing. 

11) Locate fuse holder “F1” on the PCB. 

12) Use a continuity tester to determine if the fuse has blown.  

13) If the fuse has not blown contact 

Tritech

 technical support 

for further assistance. 

14) If the fuse has blown, use a screw-driver to carefully 

remove it from its holder (the body of the fuse is glass!), and 
replace with a “

2A 250V 20

×

5mm Quick-Acting (F)

” fuse 

15) When done, fully close up the SeaHub unit, reversing the 

steps described in section 7.1. 

 

 

 

Summary of Contents for SeaHub







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands