manualshive.com logo in svg

Tritech SeaHub, Operator'S Manual

Share
Download
Tritech SeaHub Operator'S Manual Download Page 10

 

Operator Manual

 
  

Issue 1 

TIL – Eng – Spec – 080 

Page 10 of 70 

 

SeaHub 

3. Before Using  

Read the following sections carefully to learn what parts are included, gain an understanding of the 
product, its configurations and setup & installation procedures. 
 

3.1. Package Contents 

Upon delivery your SeaHub package contains the following items… 
 

 

•

  A “SeaHub Surface Interface” module 

 

•

  A mains power cord 

 

•

  A 3m USB2 (Type-A to Type-B) cable 

 

•

 Quick-start 

installation and setup guide 

•

 Manuals 

 

•

  Software & Driver CD – containing… 

Seanet Pro software 
SeaHub drivers 
Electronic Manuals (PDF format) and Acrobat PDF reader 

 

•

 Transit 

Case 

 

•

  Connection Kit - comprising… 

2 

×

 9-Way Female D-Type connectors (solder bucket) and shells 

2 

×

 6-Way DIN plugs (solder bucket) and shells 

1 

×

 15-Way Male D-Type connector (solder bucket) and shell 

3 

×

 4mm “Banana Style” plugs (red, black and green) 

1 

×

 Yellow Waterblock Adapter with 39

Ω

 internal termination resistor

 

Summary of Contents for SeaHub







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands