Tritech SeaHub Operator'S Manual Download Page 16 | Manualshive

Page: 16 / 70

background image

Operator Manual

Issue 1

TIL – Eng – Spec – 080

Page 16 of 70

SeaHub

5) Windows may display a “speech” bubble showing the

new hardware has been detected and installed. Click
the “X” in the bubble to acknowledge it.

6) The plug-and-play system should now identify that

the Serial ports now need installing, for each USB-to-
Serial converter identified by the pervious part of the
installation.

This installation is the same process as before, so
repeat the above steps to locate the driver

7) When the process is complete, the following

“success” window should be displayed.

Click “Finish” to complete the installation.

8) Windows may display a “speech” bubble showing the

new hardware has been detected and installed. Click
the “X” in the bubble to acknowledge it.

9) If prompted, reboot the PC. The drivers should then

be installed and ready to use.

«
...
14
15
16
17
18
...
»

Summary of Contents for SeaHub







































































Reviews:

No comments

Related manuals for SeaHub

Brand: Xoop Lighting Pages: 20

Brand: Vari Lite Pages: 132

Brand: Unitary products group Pages: 28

Brand: NEILPRYDE Pages: 55

Brand: HANYOUNGNUX Pages: 4

Brand: Park House Healthcare Pages: 6

Brand: J&M Pages: 33

Brand: K-9 Lights Pages: 12

Brand: Vag Pages: 10

Cell Saver Elite+

Brand: Haemonetics Pages: 230

Brand: Tadano Pages: 16

Brand: Garmin Pages: 41

Brand: Daavlin Pages: 55

Brand: Daavlin Pages: 19

Brand: Mindray Pages: 295

Brand: ZAMST Pages: 14

Brand: Pixlip Pages: 15

Brand: Becker-Elektronik Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands