manualshive.com logo in svg

Tritech SeaHub, Operator'S Manual

Share
Download
Tritech SeaHub Operator'S Manual Download Page 42

 

Operator Manual

 
  

Issue 1 

TIL – Eng – Spec – 080 

Page 42 of 70 

 

SeaHub 

6.3.3. Port C & Port D (RS232, RS485 & ArcNet) 

6-Way Female DIN connector, capable of supporting the following modes (under software selection)… 

•

  RS232 3-Wire (RX, TX, GND) 

•

 RS485 

Half 

Duplex 

•

 ArcNet 

LAN 

 
All signals are fully isolated and voltage transient with respect to the communications power supply. 
 
External DC Power (separate to that described for the DC output power sockets) is available on “POWER 
POSITIVE”. When the AC “Mains” power source is used, this will be +28V (

±

5%) DC, otherwise the DC 

source less 1.4V will be present. 
 
Hardware will support data transfer rates of up to 921,600 baud in RS232/RS485 mode. 
 

 

 

Connector face view

 

 

RS232 

RS485 

ARCNET 

1 

RX TX/RX-A 

LAN-A 

2 

TX TX/RX-B 

LAN-B 

3 

PWR 

POSITIVE 

PWR 

POSITIVE 

PWR 

POSITIVE 

4 

PWR 

GROUND 

PWR 

GROUND 

PWR 

GROUND 

5 

COMMS 

GROUND 

COMMS 

GROUND 

COMMS 

GROUND 

6 

EARTH EARTH EARTH 

Notes: 

1)  The output supply on “PWR POSITIVE” and “PWR GROUND” is isolated with respect to the Data 

signals on Pins 1 and 2. 

2)  The voltage on the Data Signals on Pins 1 and 2 are with respect to the “COMMS GROUND” on 

Pin 5. 

3)  The “EARTH” pin is electrically connected to the housing chassis and Earth pin on the Main’s 

power socket. 

4)  The “COMMS GROUND” pin 5 may be disconnected internally (by means of a jumper) if 

required. 

5)  An internal 150

Ω

 termination resistor is fitted across pins 1 and 2, when in RS485 mode. 

6)  RTS and CTS handshaking protocol not available on this port. PC Serial ports should be 

configured to use no handshaking. 

 

Summary of Contents for SeaHub







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands