Toshiba TDP-MT5 Service Manual Download Page 48

Page: 48 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

Remove and replace the power supply

The

power supply

(510-1532-xx) fastens to the metal chassis. It includes both the ballast and low

voltage components on one ECA. To remove the power supply, you remove the chassis from the

projector, then separate the power supply from the chassis.

Remove the chassis and power supply from the bottom case (page 36), and place the assembly

chassis side up on the work surface.

Remove the

controller/power supply cable

(211-0161-xx) from its connector on the power

supply. Squeeze the latch on the bottom of the connector to release it.

Turn the chassis over so that the power supply faces upward.

Unplug the

safety switch cable

(211-0162-xx) from its connector on the power supply.

Summary of Contents for TDP-MT5













































































































Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands

Toshiba TDP-MT5, Service Manual

Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands