Toshiba TDP-MT5 Service Manual Download Page 17

Page: 17 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

Remove and replace the lamp door and lamp module

The

lamp module

(SP-Lamp-LP5E) consists of a reflector assembly and frame. The reflector assembly

contains a metal halide arc and a reflector. A frame made of metal and plastic holds the reflector

assembly in place inside the projector.

The

lamp door

(TDP-S3/T3: 505-0978-xx; TDP-MT5: 505-1196-xx) fits over the lamp cavity. It includes a

tab that closes the interlock switch when the door is shut.

CAUTION!

The lamp module gets very hot during operation. Allow the lamp to cool for 30 minutes before

handling it.

Place the projector upside down on the work surface.

To remove the lamp door, press the lip on the outside edge of the door until the door slides

inward. Then swing the door open.

Loosen the two captive screws that secure the lamp to the lamp housing.

Summary of Contents for TDP-MT5













































































































Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands

Toshiba TDP-MT5, Service Manual

Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands