Toshiba TDP-MT5 Service Manual Download Page 64

Page: 64 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

Upgrading the software

To upgrade the software, you need the M1-A cable (210-0185-xx) that ships with the

projector. You also need to download the software (page 60) and install the software on your computer

(page 61).

Special Note

Before you begin the software upgrade process, make sure that you have properly loaded

into your computer the system software and drivers included in the software you

downloaded from the Toshiba web site. Otherwise the upgrade will not work.

Connect the projector to the computer with the M1-A cable

Plug the M1-A cable into the projector and computer as shown in the illustration below. You don't

need to plug in the monitor cable.

Plug the power cord into the projector and into a power source.

NOTE

The instructions below apply to both the TDP-S3, the TDP-T3 and the TDP-MT5. The

TDP-T3 is referenced in the examples, but they apply to the TDP-S3 Mt-5 as well. The only

difference is that the three projectors use different software.

Open Windows Explorer, navigate to the batch file, then double-click the FlashUSB utility.

Summary of Contents for TDP-MT5













































































































Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands

Toshiba TDP-MT5, Service Manual

Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands