Toshiba TDP-MT5 Service Manual Download Page 62

Page: 62 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

The filename T3v29.exe means that this is version 2.9 of the system software for the TDP-T3.

The version number changes each time the software is updated.

The WinZip Self-Extractor dialog box appears.

Leave the folder choice as c:\T3\v2.9. Click

Unzip

. WinZip extracts the files to c:\T3\v2.9

NOTE

If you can't find the file, use the Windows Find feature to locate the file. On the Tools

menu, point to Find, then click Files or Folders. In the Find dialog box, enter the name of

the file (for example,

T3v29.exe

Click OK in the message box that appears, then click

Close

NOTE

Follow steps five through seven if you are using

Windows 98

. If you are using a computer

that runs on

Windows 2000

, steps five through seven are not necessary.

In Windows Explorer, navigate to the folder C:\T3\v2.9 (or the directory in which you saved the

file, if different).

Summary of Contents for TDP-MT5













































































































Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands

Toshiba TDP-MT5, Service Manual

Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands