Toshiba TDP-MT5 Service Manual Download Page 52

Page: 52 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

Remove and replace the power supply fan and safety switch cable

The

power supply fan

(526-0098-xx) fastens to the metal chassis. It faces inward (label side in) so that it

blows cool air through the power supply. At the same time you remove the power supply fan cable, you

also remove the

safety switch cable

(211-0162-xx), which runs between the power supply and the

interlock switch assembly.

To remove and replace the safety switch cable, do the following:

Remove the chassis and power supply from the bottom case (see page 36).

Place the chassis on the work surface so that the power supply faces upward.

Unplug the safety switch cable from its connector on the power supply

Turn the chassis and power supply over on the work surface.

To remove the safety switch cable, lift it out of the three cable retainers on the chassis.

Summary of Contents for TDP-MT5













































































































Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands

Toshiba TDP-MT5, Service Manual

Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands