Toshiba TDP-MT5 Service Manual Download Page 13

Page: 13 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

Remove and

replace

the front bezel and front bezel vent

The

front bezel

(TDP-S3/T3: 505-0972-xx;TDP-MT5: 505-1193-xx) fastens to the front of the projector.

The

front bezel vent

(TDP-S3/T3: 505-0969-xx; TDP-MT5: 505-1195-xx), in turn, fastens to the front

bezel. The

Toshiba nameplate

(TDP-S3/T3, 505-1060-xx; TDP-MT5, 505-1197-xx) snaps to the front of

the front bezel vent.

To remove the bezel vent, do the following:

Remove the focus and zoom rings (see page 11).

Use a small bladed screwdriver to pry off the Toshiba nameplate. The nameplate covers the

screws on the front bezel vent.

Use a T-10 driver to remove the M3x14 Torx screw on the end of the vent opposite the projection

lens.

Summary of Contents for TDP-MT5













































































































Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands

Toshiba TDP-MT5, Service Manual

Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands