Toshiba TDP-MT5 Service Manual Download Page 43

Page: 43 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

Remove and replace the chassis

The metal

chassis

(330-0702-xx) provides the necessary rigidity for the projector’s internal components,

yet it adds very little to the overall weight.

Remove the controller ECA (see page 29).

Remove the M3x6 Torx screw that fastens the

ground clip

(320-00724-xx) to the chassis

adjacent to the DMD/controller connector. Then lift the ground clip off of the chassis. Set the

ground clip aside. You need to fasten it to the new chassis.

Remove the Chassis and power supply (see page 36)

Place the chassis on the work space and remove the following parts:

Power supply fan and interlock switch cable (see page 52)

Power supply(see page 48)

Rear bezel (includes diode gap pad, heat sink and power supply insulator) (see page 40)

You are left with the bare chassis.

Assembly Notes

♦

Install the ground clip before you install the chassis and parts in the bottom case.

♦

Torque the M3x6 Torx screw on the ground clip to 6 in/lbs (.68 Nm).

Summary of Contents for TDP-MT5













































































































Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands

Toshiba TDP-MT5, Service Manual

Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands