Toshiba TDP-MT5 Service Manual Download Page 51

Page: 51 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

Do one of the following:

If you are replacing the power supply with a new one, follow the assembly notes below.

—Or—

Click the part below that you need to replace.

Rear bezel (see page 40)

Chassis (see page 43)

Assembly Notes

♦

Make sure the gap pad, the heat sink clip and the paper insulator are in place before you install the

power supply. Go to page 40 for more information.

♦

Align the power supply with the screw holes on the chassis. Once the power supply is in place, flex

the rear bezel outward so that the power supply ECA will clear the tab in the center of the rear bezel.

See step 6 above.

♦

Torque the six M3x8 Torx screws to 6 in-lbs (.68 Nm). See step 5 above for screw locations.

♦

Connect the ground wire to the post near the AC connector. Make sure that you route the wire as

shown below.

♦

Connect the interlock switch cable to its connector on the front of the power supply. See step 4

above.

Summary of Contents for TDP-MT5













































































































Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands

Toshiba TDP-MT5, Service Manual

Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands