Toshiba TDP-MT5 Service Manual Download Page 40

Page: 40 / 108

TDP-S3/TDP-T3/TDP-MT5 Service Manual

Remove and replace the rear bezel

The

rear bezel

(TDP-S3/T3: 505-0966-xx; TDP-MT5:

505-1129-xx

) fastens to the metal chassis. The

rear

bezel label

(020-1177-xx) adheres to the outside of the rear bezel.

When you access the rear bezel, you also remove the

power supply insulator

(TDP-S3/T3: 329-0268-xx

TDP-MT5: 329-0321-xx), the

diode gap pad

(329-0301-xx), and the

diode heat sink bracket

(330-0724-

xx). These three parts provide thermal and electrical protection for the power supply.

Remove the chassis and power supply from the bottom case (see page 36).

Remove the power supply from the chassis (see page 48).

Place the chassis on the work surface so that the paper power supply insulator faces upward.

Remove the M3x6 Torx screw that secures the diode heat sink bracket to the chassis, then

remove the heat sink and attached gap pad.

Remove the gap pad. Place it in a secure location so that it does not get lost.

Summary of Contents for TDP-MT5













































































































Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands

Toshiba TDP-MT5, Service Manual

Search results

Summary of Contents for TDP-MT5

Reviews:

Related manuals for TDP-MT5

Brands by name

Popular brands