Toshiba OIS PLUS Series User Manual Download Page 65

Page: 65 / 131

Procedure to mount the unit:

Gasket

Mounting

Clamp

Mounting

Hardw are

Mounting Hardw are is a set of cap nut, screw & clamp

Figure - 1

Figure - 2

Figure - 3

Figure - 4

Make a cut-out of the required size. Panel cut-out tolerance is +0.00mm. Put the gasket behind the bezel.

The gasket may be sealed to the case using adhesive.

FIGURE - 1

There are four (4) slots provided on the unit case to mount the unit.

FIGURE - 2

A set of four (4) mounting hardware is provided with each OIS

PLUS3 unit.

(It is consist of single cap nut, screw and clamp)

Screw

Clam p

Cap Nut

FIGURE - 3

Insert the clamp into the slot provided on the unit case. hold the unit straight.

Tighten the mounting screws evenly to a torque between 0.5 and 0.6 Nm.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for OIS PLUS Series




































































































































Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands

Toshiba OIS PLUS Series, User Manual

Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands