Toshiba OIS PLUS Series User Manual Download Page 130

Page: 130 / 131

27.

Following popup window will appear on system tray to indicate successful installation.

Note: Windows might skip some of the windows, while installing the driver on USB ports.

9.2 Cannot Install the HMI USB Driver

All OIS PLUS have at least one Com port. The OIS PLUS can be programmed and monitored thru the COM 1

port using the serial cable IBM-0909-1-00. This cable can be purchased from Toshiba or made as follows:

DO NOT

connect any other wires than those shown above. Other pins are used for different purposes and

connecting these could interfere with the programming cable.

Computer Side

OIS PLUS Side

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for OIS PLUS Series




































































































































Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands

Toshiba OIS PLUS Series, User Manual

Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands