Toshiba OIS PLUS Series User Manual Download Page 109

Page: 109 / 131

6.1 Overview

OIS PLUS clip-on analog modules can accept a number of different types of inputs and produce

different types of outputs. To determine which type of input and which type of output the module

used, a profile for the modules must be setup in the MW registers. The group of MW registers

assigned to the module is determined by the modules mounting position. The OIL-DS software is

used to assigned values to the MW registers. The following table shows the relationship between the

MW configuration registers, XW input registers, and the YW output registers.

Description

Expansion Slot

Slot1

Slot2

Slot3

Slot4

Slot5

Input

egi

Analog Input (CH0)

Type- Slotxx

MW0100

MW0200

MW0300

MW0400

MW0500

Analog Input (CH1)

Type- Slotxx

MW0101

MW0201

MW0301

MW0401

MW0501

Analog Input (CH2)

Type- Slotxx

MW0102

MW0202

MW0302

MW0402

MW0502

Analog Input (CH3)

Type- Slotxx

MW0103

MW0203

MW0303

MW0403

MW0503

Input Register(CH0)-

Slotxx

XW0100

XW0101

XW0200

XW0201

XW0300

XW0301

XW0400

XW0401

XW0500

XW0501

Input Register(CH1)-

Slotxx

XW0102

XW0103

XW0202

XW0203

XW0302

XW0303

XW0402

XW0403

XW0502

XW0503

Input Register(CH2)-

Slotxx

XW0104

XW0105

XW0204

XW0205

XW0304

XW0305

XW0404

XW0405

XW0504

XW0505

Input Register(CH3)-

Slotxx

XW0106

XW0107

XW0206

XW0207

XW0306

XW0307

XW0406

XW0407

XW0506

XW0507

put

egi

Analog Output (CH0)

Type- Slotxx

MW0104

MW0204

MW0304

MW0404

MW0504

Analog Output (CH1)

Type- Slotxx

MW0105

MW0205

MW0305

MW0405

MW0505

Output Register(CH0)-

Slotxx

YW0100

YW0200

YW0300

YW0400

YW0500

Output Register(CH1)-

Slotxx

YW0101

YW0201

YW0301

YW0401

YW0501

All analog modules are configured as shown above depending on their slot number. Beyond the

above each module must be setup individually.

Note: All settings are in decimal.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for OIS PLUS Series




































































































































Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands

Toshiba OIS PLUS Series, User Manual

Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands