Toshiba OIS PLUS Series User Manual Download Page 103

Page: 103 / 131

5.4 Fixed Pulse Mode PWM Output

To configure high speed output in fixed pulse mode (Trapezoidal / soft start) follow the steps below:

1) Create a new application

2) Add expansion FPED-HS-0808N in slot1

3) Set 'PWM configuration resister' on screen

4) Put value as 9 in 'PWM configuration resister'

5) Set 'Minimum frequency setting resister' on screen and put its value as '4'

6) Set 'Maximum frequency setting resister' on screen and put its value as '100'

7) Set 'Acceleration time register' and set it value as 32000

8) Set 'Deceleration time register' and set it value as 32000

9) Set 'Total pulse count' register and set value as 5000

10) Set elapsed time on screen

11) Download application

This will RUN the operation in fixed pulse mode (trapezoidal / soft start).

Note:

Minimum frequency should be maximum 10,000.

In this mode, fixed number of pulses can be output on the Y2 of expansion of transistor outputs of the unit

according to the specified parameter.

The function selection is done using Configuration register MW0124 (for Slot 1).

When the corresponding control flag is off and the execution condition (trigger) is in the on state, a pulse is

output from the specified output (Y2).

The control code, minimum frequency, maximum frequency, acceleration time, deceleration time and total

number of pulses are specified by a user program as shown in the following table.

The frequency is switched by the acceleration/deceleration time specified for changing from the initial speed

to the maximum speed. The acceleration and deceleration is normally done in 30 steps.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for OIS PLUS Series




































































































































Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands

Toshiba OIS PLUS Series, User Manual

Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands