Toshiba OIS PLUS Series User Manual Download Page 99

Page: 99 / 131

5.2 CW/CCW Mode PWM Output

To configure the high speed output in CW/CCW mode follow the steps below:

1) Create a new application.

2) Add a clip-on module in slot1

3) Set 'PWM configuration resister' on screen

4) Put value as 3 in 'PWM configuration resister'

5) Set 'frequency setting resister' on screen and put its value as '+5000'

6) Set enable flag resister on screen and keep its status as 'ON"

7) Set 'Frequency setting error flag' on screen

8) Download application

This will RUN the operation in CW/CCW mode.

Note:

The value of 'Frequency setting resister should be in between +/-1 to +/-10,000

If value of 'Frequency setting resister' is less than 1 or greater than 10,000 then, frequency setting error flag

will be 'ON' otherwise it will be OFF.

When CW/CCW mode is selected and if frequency data range is positive, match output 6(MR6) will be

selected so that pulses will be out on Y2 and if frequency data range is negative, match output 1(MR1) will

be selected so that pulses will be out on Y4.

Function

Remarks

CW Pulse

CCW Pulse

Pulse enable flag

MW0136_0

Output is enabled when ON

Frequency setting register

MW0125

MW0126

Data range: -10000 to –1, 1 to 10000

Frequency setting error flag

MW0129_3

ON at error (Reset OFF automatically)

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for OIS PLUS Series




































































































































Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands

Toshiba OIS PLUS Series, User Manual

Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands