Toshiba OIS PLUS Series User Manual Download Page 64

Page: 64 / 131

2.6 Installation Instructions

The OIS PLUS should be mounted on a panel. A sealing gasket and mounting clamps are provided with each

OIS PLUS unit for proper installation.

Environmental Considerations:

Make sure that the unit is installed correctly and that the operating limits are followed (see Specifications for

OIS PLUS). Do not operate the OIS PLUS in areas subject to explosion hazards due to flammable gases,

vapors or dusts. A OIS PLUS should not be installed where fast temperature variations are present. Highly

humid areas are also to be avoided. High humidity causes condensation of water in the unit.

Location Considerations:

Care should be taken when locating equipment behind the OIS PLUS to ensure that AC power wiring, PLC

output modules, contactors, starters, relays and any other source of electrical interference are located away

from the OIS PLUS. Particular care should be taken to locate variable speed drives and switching power

supplies away from the OIS PLUS.

Panel Mounting

This section presents the dimensional sketches and panel cutouts for OIS PLUS

models. (All dimensions are in mm and drawings are not to scale.)

2.6.1 Panel Cut-out and Mounting for OIS45 & 55 PLUS Models

Below given panel cut-out and mounting information is applicable to model with 3.5” LCD and 4.3” LCD.

Panel cut-out:

Note: Maximum panel thick ness should be 6.5mm (Tolerance: +0.00mm).

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for OIS PLUS Series




































































































































Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands

Toshiba OIS PLUS Series, User Manual

Search results

Summary of Contents for OIS PLUS Series

Reviews:

Related manuals for OIS PLUS Series

Brands by name

Popular brands