107
SMMS 2-way Air Discharge Cassette Type
Installation Manual
22
8
APPLICABLE CONTROLS
REQUIREMENT
When using the air conditioner for the first time, it will
take some moments after the power has been turned on
before the remote controller becomes available for
operations: This is normal and is not indicative of trouble.
• Concerning the automatic addresses (The automatic
addresses are set up by performing operations on the
outdoor interface circuit board.)
While the automatic addresses are being set up, no
remote controller operations can be performed. Setup
takes up to 10 minutes (usually about 5 minutes).
• When the power is turned on after automatic address
setup
It takes up to 10 minutes (usually about 3 minutes) for
the outdoor unit to start operating after the power has
been turned on.
Before the air conditioner was shipped from the factory,
all units are set to [STANDARD] (factory setting). If
necessary, change the indoor unit settings.
The settings are changed by operating the wired remote
controller.
* The settings cannot be changed using only a wireless
remote controller, simple remote controller or group
control remote controller by itself so install a wired
remote controller separately as well.
Ba
sic procedure for changing
settings
Change the settings while the air conditioner is not
working. (Be sure to stop the air conditioner before
making settings.)
Requirement when setting the CODE No.
Set only the CODE No. shown in the following table: Do
NOT set any other CODE No.
If a CODE No. not listed is set, it may not be possible to
operate the air conditioner or other trouble with the
product may result.
* The displays appearing during the setting process
differ from the ones for previous remote controllers
(AMT31E). (There are more CODE No.)
1
6
1
3
2
5
4
1
Pu
ld
an
MP.”
button
r
t
.
• If t
COD
s
h
button to
clear the di
ay
eat the
pr
om
o
o of
the re
ntr ller
a
fte
ff r
d.)
(
ers are operated under the
LL” is displayed first. When
is
, the indoor unit number
ng “ALL” is the header unit.)
(* Display content varies
ith
indoor un
r
it
model.)
2
Each time you pu
do
nit
numbers i
cally.
Select
u w
ch
ttings
for.
The fan of the selected unit runs and the louvers
start swinging. You can confirm the indoor unit for
which you want to change settings.
3
Usin
P.
/
buttons,
specify
CODE
No. [
4
“
”
/
buttons, select SET
DAT
A
A
[
].
5
Pu
n. When the display changes from
ng
up is completed.
• T
i
of another i
r ndoor unit, repeat
from P
.
• T
e selected indoor
un t, re
ro
3
.
Use
to
ttings. To make
tton
as
hed, repeat from
ur
6
When se
ave been completed, push
the setting
but
is pushed,
fl
s and then
y
ent disappears
con
ters the normal st
(While
is flashing, no operation of th
f
e remote
controller is accepted.)
Installing indoor unit on high
ceiling
When the ceiling on which the indoor unit is to be
installed is higher than 2.7 meters, the air volume must
be adjusted so establish the high-ceiling setting.
• Follow to the basic operation procedure
(
1
→
2
→
3
→
4
→
5
→
6
).
• For the CODE No. in Procedure
3
, specify [5d].
• Select the SET DATA for Procedure
4
from the “Height
list of ceiling possible to be installed” table in this
manual.
When installing separately sold
filters
Be sure to make Filter setting when installing separately
sold filters.
* Separately sold filters cannot be installed in an indoor
unit on a high ceiling.
• The operating procedure is the same as that for
“Installing indoor unit on high ceiling.”
• As the SET DATA in procedure
4
, select the SET
DATA of the filter installed from the table below.
SET DATA
Filter
0000
Normal filter (Factory setting)
0001
Super long life filter
SETTING
EN-43
EN-44
