Toshiba Estia RUA-CP1701H Installation Manual Download Page 35

Page: 35 / 94

Monobloc Outdoor Unit Installation Manual

Boiler ON/OFF DHW cylinder heater connection (optional)

Depending on the configuration, it is possible to control up to three electric heaters or three electric heat stages

i) One electric heat stage with one customized discrete output: EH1

ii) Two electric heat stages with two customized discrete outputs: EH1 and EH2

iii) Three electric heat stages with two customized discrete outputs: EH1 and EH2

iv) Three electric heat stages* with three customized discrete outputs: EH1 and EH2 and EH3.

This configuration cannot be activated if DHW heater is present.

The boiler ON/OFF and the stage 1 electric heater use the same output. It is not possible to operate the boiler ON/

OFF and the stage 1 electric heater at the same time.

Each discrete output can control a contactor (not supplied with the unit).

7.8.13 External electrical connections – digital outputs (230VAC relay)

Function

Description

DO#01

Main water pump ON/OFF

DO#03

Additional water pump ON/OFF

DO#04

No function (future development)

Relay

Out 230 VAC - 5 A

Unused

Additional WP On/Off (fixed speed)

Main Water Pump On/Off

Neutral

Tmax.

Summary of Contents for Estia RUA-CP1701H































































































Search results

Summary of Contents for Estia RUA-CP1701H

Reviews:

Related manuals for Estia RUA-CP1701H

Brands by name

Popular brands

Toshiba Estia RUA-CP1701H, Installation Manual

Search results

Summary of Contents for Estia RUA-CP1701H

Reviews:

Related manuals for Estia RUA-CP1701H

Brands by name

Popular brands