Toshiba e-STUDIO Troubleshooting Manual Download Page 88 | Manualshive

Page: 88 / 134

background image

3 TROUBLESHOOTING FOR PRINTING

86 Print Job Problems

Print Job Problems

This section describes how to clear the print jobs errors.



Clearing print job errors

Problem Description

A print job error occurs and [JOB STATUS] blinks when the paper specified by the computer is not set in the drawers of the
equipment.

Corrective Action

Clear the error following the procedure below.

To print by placing paper on the bypass tray

1

Press the [JOB STATUS] which is blinking.

2

Place paper of the size specified with the computer on the bypass tray, and press the
[START] button.

Printing starts. Press [JOB STATUS] when printing has been completed.

Printing by selecting a paper size already placed in another drawer

You can perform printing with the paper already placed in the drawers. Some part of the image may not be printed,
however, if the paper size in the drawer is smaller than the one you have specified.
Press the drawer button you intend to use on the touch panel and press the [START] button.

«
...
86
87
88
89
90
...
»

Summary of Contents for e-STUDIO







































































































































Reviews:

No comments

Related manuals for e-STUDIO

imagePROGRAF iPF760

Brand: Canon Pages: 12

imagePROGRAF iPF825 MFP Basic Guide No.1

Brand: Canon Pages: 16

imagePRESS C850

Brand: Canon Pages: 146

imagePRESS C850

Brand: Canon Pages: 63

imagePROGRAF iPF760

Brand: Canon Pages: 132

imagePROGRAF iPF825 MFP Basic Guide No.1

Brand: Canon Pages: 8

imagePROGRAF TX-2000

Brand: Canon Pages: 14

i-SENSYS MF6180dw

Brand: Canon Pages: 1040

imagePROGRAF iPF815

Brand: Canon Pages: 48

imageRUNNER 1025

Brand: Canon Pages: 6

imageRUNNER 2230

Brand: Canon Pages: 6

IMAGEPRESS C7010VPS

Brand: Canon Pages: 388

Brand: Canon Pages: 56

imagePROGRAF iPF8300

Brand: Canon Pages: 24

imagePROGRAF iPF8300

Brand: Canon Pages: 4

imagePROGRAF iPF6350

Brand: Canon Pages: 12

imagePROGRAF iPF6350

Brand: Canon Pages: 2

imageCLASS MF8380Cdw

Brand: Canon Pages: 192

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands