Toshiba e-STUDIO Troubleshooting Manual Download Page 130 | Manualshive

Page: 130 / 134

background image

8 WHEN SOMETHING IS WRONG WITH THE EQUIPMENT

128 Regular Maintenance

Regular Maintenance

We recommend that you clean the following portions weekly so that the originals can always be scanned in unsoiled
conditions.



Be careful not to scratch the portions when cleaning them.



When cleaning the surface of the equipment, do not use such organic solvents as thinner or benzine.

-

This could warp the shape of the surface or leave it discolored.

-

When using a chemical cleaning pad to clean it, follow the instructions.

1. Scanning area (surface of the long rectangular glass) / 2. Original glass

Wipe it with a soft dry cloth. If there are still stains remaining, wipe clean with a piece of soft cloth which has been
moistened with water and then squeezed well. Do not use liquids other than water (such as alcohol, organic solvents
or neutral detergent).

3. Guide / 4. Platen sheet

Clean the surface as follows depending on the extent of the staining.



Clean it with a soft cloth.



Clean it with a soft cloth lightly moistened with water.



Clean it with a soft cloth lightly moistened with alcohol, and then wipe with a dry cloth.



Clean it with a soft cloth lightly moistened with watered-down neutral detergent, wipe with a cloth moistened with
water, and then wipe with a dry cloth.

1

2

3

4

«
...
128
129
130
131
132
...
»

Summary of Contents for e-STUDIO







































































































































Reviews:

No comments

Related manuals for e-STUDIO

Brand: Datecs Pages: 73

Brand: Datamax Pages: 12

E-Class Mark II

Brand: Datamax Pages: 40

Brand: Datamax Pages: 46

Brand: Olivetti Pages: 2

Brand: Olivetti Pages: 109

Brand: Olivetti Pages: 111

Brand: Olivetti Pages: 8

imageRUNNER 5075

Brand: Canon Pages: 250

MC560 MFP CX2032

Brand: Oki Pages: 247

Brand: Ricoh Pages: 781

Komax ims 295 BC

Brand: WIEDENBACH Pages: 52

Brand: Oce Pages: 686

PS100 - Photo Printer - 50 Sheets

Brand: Olympus Pages: 2

Brand: Xerox Pages: 233

Brand: Delta OHM Pages: 28

Brand: E-Pos Pages: 21

Brand: Axiohm Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands