manualshive.com logo in svg

Toro Greensmaster 1018, Service Manual

Share
Download
Toro Greensmaster 1018 Service Manual Download Page 82

Disassembling the Transmission Gear Box Assembly (continued)

8. Use a press to remove the 2 ball bearings (13) and 2 flange bearings (12)

from the differential assembly (14). Remove the V-ring seal (15) from the
differential assembly (14). Discard the ball bearings (13).

9. If necessary, disassemble the differential assembly (14); refer to

Disassembly

of Differential Assembly (page 5–37)

.

10. Remove the bolt (25) that secures the cable brake lever (24) onto the brake

lever (19). Slide and remove the cable brake lever (24) and external retaining
ring (1) from the brake lever (19).

11. Remove the 4 bolts (8) that secures the retainer plate (16) to the transmission

housing assembly (23). Remove the retainer plate (16) from the transmission
housing assembly (23).

12. Slide and remove the brake lever assembly (19) from the transmission

housing assembly (23). Remove the flat wire spring (22) from the
transmission housing assembly (23).

13. Disassemble the brake lever assembly (19) as follows:

A. Remove the retaining ring (17) from the brake clevis pin (21).

B. Slide and remove the brake clevis pin (21) from the brake band (18)

and brake lever (19).

C. Remove the brake lever (19) from the brake band (18).

D. Remove and discard the O-ring (20) from the brake lever (19).

Traction and Reel Drive Systems: Service and Repairs

Page 5–28

Greensmaster

®

1018/1021/1026

18238SL Rev B

Summary of Contents for Greensmaster 1018




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands