Toro Greensmaster 1018 Service Manual Download Page 29

Page: 29 / 179

Cutting Reel Shim

Toro Part No. 125–5611

Use the 0.05 mm (0.002 in) shim like a feeler gauge to
measure the gap between the reel and the bedknife during
reel adjustment.

Cutting Performance Paper

Toro Part No. 125–5610

(300 strips)

Cutting performance paper is used to test the cutting reel
performance after adjusting the reel to bedknife clearance.

Backlapping Brush Assembly

Toro Part No. 29–9100

For applying lapping compound to cutting units while keeping
hands a safe distance from the rotating reel.

Components for the brush assembly are also available
individually.

Brush 36-4310

Handle 29-9080

Handle cap 2410-18

Reel Drive Shaft

K-Line Part No. TOR4112

Use the drive shaft for rotating the reel during cutting unit
adjustment or any time the cutting unit motor is removed.

Greensmaster

1018/1021/1026

Page 2–15

Specifications and Maintenance: Special Tools

18238SL Rev B

Summary of Contents for Greensmaster 1018




















































































































































































Search results

Summary of Contents for Greensmaster 1018

Reviews:

Brands by name

Popular brands

Toro Greensmaster 1018, Service Manual

Search results

Summary of Contents for Greensmaster 1018

Reviews:

Brands by name

Popular brands